Paper mold equipment and products companies must not be short-sighted

In the “white pollution” contingent, the pulp molding industry has “broadly” developed, including molding equipment, chemical additives, paper-molded products and other supporting companies. It is said that there are more than 300 companies. Today, only a few years ago, the molding machinery companies that were called the "four small groups" had already lost three. The product companies that purchased these small group equipment in the year were unable to operate normally due to equipment failure, and they also closed down one after another. Some existing companies have only a few climates. The reason is that this emerging industry has a generally weak sense of quality. First, paper mold machinery enterprises must pay attention to the quality of paper molding machinery is a set of mechanical, electronic, hydraulic, pneumatic, papermaking pulp, automation as one of the high-tech products. So far, the country does not have a uniform product standard for this industry. Under such circumstances, the research and production companies that research and produce such equipment should pay more attention to the quality of the product. At this point, some of our paper mold equipment manufacturing companies did not do so in the past, which misled some blindly launched personal and collective investments. The purchased equipment, even the equipment manufacturers, did not debug well and had to make modifications themselves. If they cannot reform themselves, they must become a pile of ornaments and scrap iron. The introduction of sales commissions from equipment manufacturers will only be a deductible and will not bear any quality responsibility. This is my personal experience and experience with some of my colleagues. Those who are good in quality and those who are in bad quality fail in industry. This is a common lesson learned by some companies that have lost machinery and products. After vicissitudes and vicissitudes, in today's fierce competition in replacing "white" alternative products, paper mold machinery enterprises must not only continue to develop new models of high efficiency and energy saving, but also continue to develop new raw materials and new additives to reduce the cost of products. (1) In accordance with the rules of the machinery industry, in the absence of a unified product quality standard in the country, companies must seriously formulate their own product quality standards with reference to related products. (2) Designing products must understand some relevant technical parameters required for product structure. For example, designing pulp molding equipment must understand the various parameters required for pulp wet forming (various pulp raw materials, chemical additives, and production environments, etc.) The influence of the factors), based on these parameters, the design of each item is further strictly calculated to ensure the reliability of the equipment. (3) Strict quality management must be implemented in the production process of the equipment and strictly controlled. (4) Before the equipment is sold, it must go through the product's styling appraisal and production appraisal. It must be tested according to the design requirements. It will not reach the standard and will never leave the factory. (5) Drawings must be provided to the buyer so that the manufacturer can check, use, and maintain according to the drawings. (6) Must have a quality commitment to its own product. Second, product companies must also pay attention to the quality of the recent product quality has a very important business owners, in the Beijing market, bought a few cents a price of nine cents a field of paper boxes sold in Beijing, went home to resist Oil, water resistance test. At first, we poured boiled water into the paper lunch box. As a result, the water leaked out. Then we conducted an oil-resistance test and poured hot oil into the box. As a result, we had to pour it out immediately. Otherwise, the oil would flow over the floor. Such companies use cutting-edge materials to reduce costs and market competition regardless of product quality. I don't know that companies that produce such products do not know how much space there is in this area. Therefore, I think that in order to survive in the paper mold industry and to develop industries, we must pay attention to the quality of products. To start a business, we must do the following: (1) The product company must carry out a careful inspection and understanding of the equipment it plans to purchase. The criteria for the inspection are: “How to choose a paper molding product molding machine” published by China Packaging News. "A text for reference. (2) It is recommended not to use the equipment for inspection if it is necessary to pay for orders first. In general, people who are afraid of watching must be tricky. (3) Try to contact the manufacturer using the equipment to check the operation of the equipment. (4) It is necessary to train its own technical force, and each position must have a professional technician responsible. (5) Formulating its own "corporate standards" based on the "national standards" of products and establishing a strict quality management system. Each employee must be made aware of the relationship between "Qingyeyeye" and the industry, the relationship with his own company, and his own interests, and firmly establish the "Quality Industry" consciousness. (6) To establish a quality management system, it is necessary to establish its own quality inspection room, which should be able to carry out inspections on raw materials, chemical auxiliaries and products that are most easily exceeded. (7) On the basis of strict quality management, apply for quality certification to the quality certification department for product marketing.